Skip to content

ADAPTORS / JOINT PARTS

Rotatable Intermediate Hinge

Request a quote
The intermediate joint connects two arm sections of the X-M support-arm system through a rotary connection. Its additional joint axis allows the sections to pivot relative to one another in the horizontal plane and the connected operator enclosure to be aligned. Positioned between the profile sections, the component adds movement to their connection and forms an articulated connection point within the support-arm assembly.
Weight
2060 g
Material
Aluminum
Colour
RAL 7035 / Cover RAL 7016
Package Dimensions
250 × 130 × 125 mm
HS Code
7606.99.90.19
Warranty
5 years

Technical data

Specifications for planning, selection and use at a glance.

Material & finish

Material Composition
Aluminum
Colour
RAL 7035 / Cover RAL 7016
RAL colours
RAL 7035 / RAL 7016

Application & function

Operating Weight
2060 g
Primary Use Case
Machine Building / Automation / HMI operator stations
Operating Temperature
–40°C to +70°C
Protection Rating
–IP65 (DIN EN 60529)
Rated Voltage
Mechanical (not subject to electrical certification)
Movement
Rotatable 315°
Rotation angle
315 deg

Safety & compliance

Earthing
Yes, integrated solution
RoHS Compliance
RoHS EU Directive 2011/65/EU
REACH Compliance
REACH Regulation 1907/2006/EC
Certification
IEC 60529; (EG) No. 765/2008; (EU) 2023/956

Version & enquiry

Use the item number and version to prepare your enquiry.

  • SKU: X-M-ZG01

    Weight (g)
    2060

Product documents

Product files and documentation together in one place.

3 files

ZIP 1 file
PDF 2 files
  • X-M-ZG01-Produktunterlagen-DE.pdf

    1.6 MB

  • X-M-ZG01-Produktunterlagen-EN.pdf

    1.6 MB

Assembly instructions

About these instructions

Assembly sequence prepared from the exact XINDUX article data sheet. Tightening torques not specified in the source document are deliberately not added.

Preparation & tools

Supplied and installation parts

Supplied and installation parts

Required tools

  • Allen key suitable for the fasteners
  • Torque wrench for the final engineering check

Step 1 / 12 · Fasten the connection

  1. Fasten the connection

    1. Fasten the connection

    Insert the angle bolts into their slots and tighten.

    • M6 × 20
  2. Insert the gasket

    2. Insert the gasket

    Remove the yellow tape. Place the gasket with the adhesive surface facing inwards.

  3. Connect the profile

    3. Connect the profile

    Completely establish the first profile connection shown.

  4. Inspect the assembly

    4. Inspect the assembly

    Check whether the assembly is as shown in the figure.

  5. Align the system

    5. Align the system

    M6 × 20 angle bolts are used to prevent profile sagging due to the heavy weight that can occur with long support arm profiles. If sagging does not occur in your application, leave the angle bolts in the tightened position. If deflection occurs in your application, loosen the M6 ​​× 30 profile bolts by 2-3 mm. Tighten the angle screws until the difference in inclination is equalized (you can use tools such as a spirit level, etc. to check the inclination). Tighten the corresponding M6 × 30 profile screws. Tighten the profile bolts.

    • M6 × 20
    • M6 × 30
    • J6.4
    • M6
  6. Align the system

    6. Align the system

    Angle bolts are used to prevent the profile from sagging due to the heavy weight that can occur with long support arm profiles.

    • M6
    • M6 × 20
  7. Set the rotation range

    7. Set the rotation range

    Attention: You can limit the clockwise and counterclockwise rotation of the module with M6 × 10 screws.

    Attention: You can limit the clockwise and counterclockwise rotation of the module with M6 × 10 screws. There are eight equally spaced holes on the module. Optionally you can set the rotation limits with two screws.

    • M6 × 10
  8. Install the cable guide

    8. Install the cable guide

    Place the plastic cable protector as shown in the illustration on the left.

  9. Connect the profile

    9. Connect the profile

    Completely establish the second profile connection shown.

  10. Insert the gasket

    10. Insert the gasket

    Remove the yellow tape. Place the gasket on both covers with the adhesive surface facing inward.

  11. Fit the cover

    11. Fit the cover

    Position and install the covers and screws as shown in the illustration.

    • M4 × 8
  12. Insert the gasket

    12. Insert the gasket

    Check whether the seal is seated well.

Select a step or use the arrows. On mobile, swipe left or right.