Skip to content

PANEL COUPLING

Ø48 Adaptor

Request a quote
The rotary panel adapter connects a Ø48 mm tubular profile to the operator enclosure. It provides the panel-side transition in a round-tube assembly and adds a rotary function directly at the operating unit. This connection allows the connected panel to be aligned. Positioned between the tubular profile and enclosure, the adapter forms the articulated attachment of the operating device at this point in the assembly.
Weight
930 g
Material
Aluminum
Colour
RAL 7035
Package Dimensions
140 × 120 × 110 mm
HS Code
7606.99.90.19
Warranty
5 years

Technical data

Specifications for planning, selection and use at a glance.

Material & finish

Material Composition
Aluminum
Colour
RAL 7035
RAL colours
RAL 7035

Application & function

Operating Weight
930 g
Primary Use Case
Machine Building / Automation / HMI operator stations
Operating Temperature
–40°C to +70°C
Protection Rating
–IP65 (DIN EN 60529)
Rated Voltage
Mechanical (not subject to electrical certification)
Movement
Rotatable 350°
Rotation angle
350 deg

Safety & compliance

Earthing
Yes, integrated solution
RoHS Compliance
RoHS EU Directive 2011/65/EU
REACH Compliance
REACH Regulation 1907/2006/EC
Certification
IEC 60529; (EG) No. 765/2008; (EU) 2023/956

Version & enquiry

Use the item number and version to prepare your enquiry.

  • SKU: X-M-PAD02

    Weight (g)
    930

Product documents

Product files and documentation together in one place.

3 files

ZIP 1 file
PDF 2 files
  • X-M-PAD02-Produktunterlagen-DE.pdf

    1.3 MB

  • X-M-PAD02-Produktunterlagen-EN.pdf

    1.3 MB

Assembly instructions

About these instructions

Assembly sequence prepared from the exact XINDUX article data sheet. Tightening torques not specified in the source document are deliberately not added.

Preparation & tools

Supplied and installation parts

Supplied and installation parts

Required tools

  • Allen key suitable for the fasteners
  • Torque wrench for the final engineering check

Step 1 / 13 · Align the system

  1. Align the system

    1. Align the system

    Insert the switching lever into the slot. The switching lever is used to adjust the torsional rigidity of the module.

    • M5 × 16
  2. Insert the gasket

    2. Insert the gasket

    Insert the upper round seal completely and without twisting into the circumferential groove.

  3. Insert the gasket

    3. Insert the gasket

    Check the circumferential, torsion-free fit of the upper round seal.

  4. Connect the profile

    4. Connect the profile

    Insert the profile into the coupling as shown in the figure on the left.

  5. Inspect the assembly

    5. Inspect the assembly

    Check that the assembly was carried out as shown in the illustration and that the profile is seated correctly.

  6. Set the rotation range

    6. Set the rotation range

    Tighten the set screw.

    • M5 × 20
  7. Insert the gasket

    7. Insert the gasket

    Remove the yellow tape. Insert the seal to the panel support with the adhesive surface to the component without folds.

  8. Insert the gasket

    8. Insert the gasket

    Check that the seal fits all around and without wrinkles on the panel support.

  9. Fasten the module to the panel

    9. Fasten the module to the panel

    Place the module on the panel.

  10. Inspect the assembly

    10. Inspect the assembly

    Before screwing, check whether the module is correctly positioned on the panel cutout.

  11. Fasten the connection

    11. Fasten the connection

    The screws are not included in the packaging.

    The screws are not included in the packaging.

    • M6 × 30
    • J6.4
  12. Inspect the assembly

    12. Inspect the assembly

    After screwing, check that there is a solid, full-surface connection between the module and the panel.

  13. Prepare the mounting holes

    13. Prepare the mounting holes

    If required, prepare the mounting holes according to the dimensioned drawing. All dimensions are given in millimetres.

Select a step or use the arrows. On mobile, swipe left or right.