Skip to content

JOINT PARTS

Rotatable Wall-Mounted Hinge Vertical Outlet

Request a quote
The rotary wall joint attaches a vertically arranged support-arm profile in the X-M system to the side of a wall or machine structure. The vertical profile outlet defines the connection direction of the arm assembly. The joint allows the connected support arm to pivot while the wall attachment remains in place. It forms an articulated transition between the fixed mounting structure and the support arm carrying the operator enclosure.
Weight
2280 g
Material
Aluminum
Colour
RAL 7035 / Cover RAL 7016
Package Dimensions
200 × 145 × 145 mm
HS Code
7606.99.90.19
Warranty
5 years

Technical data

Specifications for planning, selection and use at a glance.

Material & finish

Material Composition
Aluminum
Colour
RAL 7035 / Cover RAL 7016
RAL colours
RAL 7035 / RAL 7016

Application & function

Operating Weight
2280 g
Primary Use Case
Machine Building / Automation / HMI operator stations
Operating Temperature
–40°C to +70°C
Protection Rating
–IP65 (DIN EN 60529)
Rated Voltage
Mechanical (not subject to electrical certification)
Movement
Rotatable 315°
Rotation angle
315 deg

Safety & compliance

Earthing
Yes, integrated solution
RoHS Compliance
RoHS EU Directive 2011/65/EU
REACH Compliance
REACH Regulation 1907/2006/EC
Certification
IEC 60529; (EG) No. 765/2008; (EU) 2023/956

Version & enquiry

Use the item number and version to prepare your enquiry.

  • SKU: X-M-WGV01

    Weight (g)
    2280

Product documents

Product files and documentation together in one place.

Data sheets with the new article numbers are not yet available. Please request the documents you need.

3 files

ZIP 1 file
PDF 2 files
  • X-M-WGV01-Connection-card-de-DE.pdf

    1.1 MB

  • X-M-WGV01-Connection-card-en-GB.pdf

    1.1 MB

Assembly instructions

About these instructions

Assembly sequence prepared from the exact XINDUX article data sheet. Tightening torques not specified in the source document are deliberately not added.

Preparation & tools

Supplied and installation parts

Supplied and installation parts

Required tools

  • Allen key suitable for the fasteners
  • Torque wrench for the final engineering check

Step 1 / 14 · Insert the gasket

  1. Insert the gasket

    1. Insert the gasket

    Remove the yellow tape. Insert the profile-side connection seal with the adhesive surface to the component into the seal holder shown without folds.

  2. Connect the profile

    2. Connect the profile

    Insert the support arm profile vertically and until it rests in the profile-side connection of the joint module.

  3. Fasten the connection

    3. Fasten the connection

    Tighten the profile bolts.

  4. Connect the grounding

    4. Connect the grounding

    Insert the grounding ball, compression spring and plastic plug into the slots provided.

  5. Set the rotation range

    5. Set the rotation range

    Note: The plastic plug and set screw should be in the same hole.

  6. Fasten the connection

    6. Fasten the connection

    Connect profile coupling housing and pivot bearing unit and fasten the connection evenly with eight M6 × 16 screws with screw lock.

    • M6 × 16
  7. Inspect the assembly

    7. Inspect the assembly

    Check whether the assembly is as shown in the figure.

  8. Prepare the components

    8. Prepare the components

    Combine the assembled top with the bottom.

  9. Set the rotation range

    9. Set the rotation range

    Attention: You can limit the clockwise and counterclockwise rotation of the module with M6 × 10 screws.

    Attention: You can limit the clockwise and counterclockwise rotation of the module with M6 × 10 screws. There are eight equally spaced holes on the module. Optionally you can set the rotation limits with two screws.

    • M6 × 10
  10. Connect the grounding

    10. Connect the grounding

    Caution: Make the ground connection and check that it is secure.

    Caution: Make the ground connection and check that it is secure.

    • M4 × 8
  11. Insert the gasket

    11. Insert the gasket

    Remove the yellow tape. Insert the cover seal with the adhesive surface to the black cover into its contour without folds.

  12. Insert the gasket

    12. Insert the gasket

    Remove the yellow tape. Insert the seal to the mounting surface with the adhesive surface to the component into the seal holder shown without folds.

  13. Fit the cover

    13. Fit the cover

    The M8 mounting screws are not included.

    Place the black screw caps on the heads of the M8 screws. The M8 mounting screws are not included.

    • M8
  14. Prepare the mounting holes

    14. Prepare the mounting holes

    If required, prepare the mounting holes according to the dimensioned drawing. All dimensions are given in millimetres.

Select a step or use the arrows. On mobile, swipe left or right.