Skip to content

ADAPTORS / JOINT PARTS

Ø130 mm Panel Tilting Adaptor - With Bellows

Request a quote
The Ø130 mm panel tilt adapter with bellows adds adjustable inclination to the enclosure connection. It is intended for the X-M and X-L support-arm systems. The tilt movement allows the orientation of the operating face to be matched to the working position. The bellows enclose the moving connection area. Positioned directly at the operator enclosure, the adapter provides the tilt function within the support-arm assembly.
Weight
1150 g
Material
Aluminum
Colour
RAL 7035 (Bellow RAL 7016)
Package Dimensions
140 × 155 × 110 mm
HS Code
7606.99.90.19
Warranty
5 years

Technical data

Specifications for planning, selection and use at a glance.

Material & finish

Material Composition
Aluminum
Colour
RAL 7035 (Bellow RAL 7016)
RAL colours
RAL 7035 / RAL 7016

Application & function

Operating Weight
1150 g
Primary Use Case
Machine Building / Automation / HMI operator stations
Operating Temperature
–40°C to +70°C
Protection Rating
–IP65 (DIN EN 60529)
Rated Voltage
Mechanical (not subject to electrical certification)
Movement
+30° / - 40°

Safety & compliance

Earthing
Yes, integrated solution
RoHS Compliance
RoHS EU Directive 2011/65/EU
REACH Compliance
REACH Regulation 1907/2006/EC
Certification
IEC 60529; (EG) No. 765/2008; (EU) 2023/956

Further information

Movement type
neigbar
Positive tilt angle
30 deg
Negative tilt angle
-40°
Compatible series
X-M / X-L

Version & enquiry

Use the item number and version to prepare your enquiry.

  • SKU: X-M-PKA02

    Weight (g)
    1150

Product documents

Product files and documentation together in one place.

3 files

ZIP 1 file
PDF 2 files
  • X-M-PKA02-Produktunterlagen-DE.pdf

    1.9 MB

  • X-M-PKA02-Produktunterlagen-EN.pdf

    1.9 MB

Assembly instructions

About these instructions

Assembly sequence prepared from the exact XINDUX article data sheet. Tightening torques not specified in the source document are deliberately not added.

Preparation & tools

Supplied and installation parts

Supplied and installation parts

Required tools

  • Allen key suitable for the fasteners
  • Torque wrench for the final engineering check

Step 1 / 9 · Fit the cover

  1. Fit the cover

    1. Fit the cover

    Push the bellows up and down until it comes loose.

  2. Prepare the components

    2. Prepare the components

    Combine the module step by step as shown in the following figure.

    • M6 × 20
    • J6.4
  3. Fasten the connection

    3. Fasten the connection

    Position and tighten the screws as shown in the illustration.

  4. Fit the cover

    4. Fit the cover

    Place the bellows back into the slots.

  5. Fit the cover

    5. Fit the cover

    Check that assembly was carried out as shown in the illustration and that the bellows is seated correctly.

  6. Insert the gasket

    6. Insert the gasket

    Remove the yellow tape. Insert the gasket so that the adhesive surface faces inward.

  7. Fasten the module to the panel

    7. Fasten the module to the panel

    Mount the module on the panel.

    • M6 × 30
  8. Fasten the module to the panel

    8. Fasten the module to the panel

    The mounting screws are not included.

    Attach the module to the panel with four M6 × 30 screws. The mounting screws are not included.

    • M6 × 30
  9. Prepare the mounting holes

    9. Prepare the mounting holes

    If required, prepare the mounting holes according to the dimensioned drawing. All dimensions are given in millimetres.

Select a step or use the arrows. On mobile, swipe left or right.