Skip to content

JOINT PARTS

Steel Interconnection Module - With Bellows

Request a quote
The connecting module with bellows joins two profile sections in the X-M support-arm system. Its joint allows the connected arm sections to pivot horizontally, adding an articulated connection point to the assembly. The bellows enclose the joint area between the profile connections. The module allows the relative position of the arm sections to be changed and the connected operator enclosure to be positioned to suit the workstation.
Weight
2200 g
Material
Steel Casting
Colour
RAL 7035 / Bellow RAL 7016
Package Dimensions
180 × 140 × 120 mm
HS Code
7606.99.90.19
Warranty
5 years

Technical data

Specifications for planning, selection and use at a glance.

Material & finish

Material Composition
Steel Casting
Colour
RAL 7035 / Bellow RAL 7016
RAL colours
RAL 7035 / RAL 7016

Application & function

Operating Weight
2200 g
Primary Use Case
Machine Building / Automation / HMI operator stations
Operating Temperature
–40°C to +70°C
Protection Rating
–IP65 (DIN EN 60529)
Rated Voltage
Mechanical (not subject to electrical certification)
Movement
Right 90° - Left 90°

Safety & compliance

Earthing
Yes, integrated solution
RoHS Compliance
RoHS EU Directive 2011/65/EU
REACH Compliance
REACH Regulation 1907/2006/EC
Certification
IEC 60529; (EG) No. 765/2008; (EU) 2023/956

Further information

Movement type
schwenkbar
Swivel angle right
90 deg
Swivel angle left
90 deg

Version & enquiry

Use the item number and version to prepare your enquiry.

  • SKU: X-M-VMF01

    Weight (g)
    2200

Product documents

Product files and documentation together in one place.

3 files

ZIP 1 file
PDF 2 files
  • X-M-VMF01-Produktunterlagen-DE.pdf

    2.1 MB

  • X-M-VMF01-Produktunterlagen-EN.pdf

    2.1 MB

Assembly instructions

About these instructions

Assembly sequence prepared from the exact XINDUX article data sheet. Tightening torques not specified in the source document are deliberately not added.

Preparation & tools

Supplied and installation parts

Supplied and installation parts

Required tools

  • Allen key suitable for the fasteners
  • Torque wrench for the final engineering check

Step 1 / 13 · Prepare the components

  1. Prepare the components

    1. Prepare the components

    The supporting axis of this module should be as in the mounting example below (at right angles). Otherwise, the mounting application is not recommended.

  2. Fasten the connection

    2. Fasten the connection

    Insert the angle bolts into their slots and tighten.

    • M6 × 20
  3. Insert the gasket

    3. Insert the gasket

    Insert the seal of the first profile connection with the adhesive surface to the component without folds.

  4. Connect the profile

    4. Connect the profile

    Insert the first support arm profile completely into the profile connection shown.

  5. Fasten the connection

    5. Fasten the connection

    Tighten the profile bolts evenly at the first profile connection.

  6. Align the system

    6. Align the system

    Check the first support arm profile with a spirit level. Only if there is visible deflection, loosen the four M6 × 30 profile bolts by 2-3 mm depending on the required correction angle, align the profile with the two M6 × 20 angle bolts and then tighten all profile bolts again.

    • M6 × 30
    • M6 × 20
  7. Insert the gasket

    7. Insert the gasket

    Insert the seal of the second profile connection with the adhesive surface to the component without folds.

  8. Connect the profile

    8. Connect the profile

    Insert the second support arm profile completely into the opposite profile connection.

  9. Fasten the connection

    9. Fasten the connection

    Tighten the profile bolts evenly on the second profile connection.

  10. Align the system

    10. Align the system

    Check the second support arm profile with a spirit level. Only if there is visible deflection, loosen the four M6 × 30 profile bolts by 2-3 mm, align the profile with the two M6 × 20 angle bolts and then tighten all profile bolts again.

    • M6 × 30
    • M6 × 20
  11. Fit the cover

    11. Fit the cover

    Install the bellows in the direction of the arrow as shown in the figure to cover the module.

  12. Fit the cover

    12. Fit the cover

    Insert the bellows coupling parts into the slots on the two ends of the bellows and tighten them well.

  13. Fit the cover

    13. Fit the cover

    Check the bellows for a good fit.

Select a step or use the arrows. On mobile, swipe left or right.