Skip to content

ADAPTORS / JOINT PARTS

90° Angle Piece

Request a quote
The fixed 90° elbow connects a horizontal support-arm profile to a vertical profile in the X-L system. It changes the direction of the profile arrangement and forms a rigid connection point, without introducing an additional rotary axis. The elbow is used where the support-arm assembly requires a fixed change of direction and movement is to be provided by other joints in the system.
Weight
1650 g
Material
Aluminum
Colour
RAL 7035 (Cover RAL 7016)
Package Dimensions
170 × 100 × 160 mm
HS Code
7606.99.90.19
Warranty
5 years

Technical data

Specifications for planning, selection and use at a glance.

Material & finish

Material Composition
Aluminum
Colour
RAL 7035 (Cover RAL 7016)
RAL colours
RAL 7035 / RAL 7016

Application & function

Operating Weight
1650 g
Primary Use Case
Machine Building / Automation / HMI operator stations
Operating Temperature
–40°C to +70°C
Protection Rating
–IP65 (DIN EN 60529)
Rated Voltage
Mechanical (not subject to electrical certification)
Movement
Fixed

Safety & compliance

Earthing
Yes, integrated solution
RoHS Compliance
RoHS EU Directive 2011/65/EU
REACH Compliance
REACH Regulation 1907/2006/EC
Certification
IEC 60529; (EG) No. 765/2008; (EU) 2023/956

Further information

Movement type
fest

Version & enquiry

Use the item number and version to prepare your enquiry.

  • SKU: X-L-WS01

    Weight (g)
    1650

Product documents

Product files and documentation together in one place.

3 files

ZIP 1 file
PDF 2 files
  • X-L-WS01-Produktunterlagen-DE.pdf

    1.9 MB

  • X-L-WS01-Produktunterlagen-EN.pdf

    1.9 MB

Assembly instructions

About these instructions

Assembly sequence prepared from the exact XINDUX article data sheet. Tightening torques not specified in the source document are deliberately not added.

Preparation & tools

Supplied and installation parts

Supplied and installation parts

Required tools

  • Allen key suitable for the fasteners
  • Torque wrench for the final engineering check

Step 1 / 13 · Fasten the connection

  1. Fasten the connection

    1. Fasten the connection

    Insert the angle bolts into their slots and tighten.

    • M8 × 20
  2. Insert the gasket

    2. Insert the gasket

    Remove the yellow tape. Insert the profile-side connection seal with the adhesive surface to the component into the seal holder shown without folds.

  3. Connect the profile

    3. Connect the profile

    Insert the profile into the coupling as shown in the figure on the left.

    • M8 × 20
  4. Align the system

    4. Align the system

    Attach the support arm profile with four M8 × 40 profile bolts and four J8.4 lock washers. Only if there is visible deflection, loosen the profile bolts by 2-3 mm, align the profile with the two M8 × 20 angle bolts and then tighten all profile bolts again.

    • M8 × 40
    • J8.4
    • M8 × 20
  5. Fasten the connection

    5. Fasten the connection

    Insert two M8 × 20 angle bolts into the threaded holes shown in the second profile connection and first tighten them fully.

    • M8 × 20
  6. Insert the gasket

    6. Insert the gasket

    Remove the yellow tape. Insert the seal of the lower connection with the adhesive surface to the component without folds.

  7. Inspect the assembly

    7. Inspect the assembly

    Check whether the assembly is as shown in the figure.

  8. Connect the profile

    8. Connect the profile

    Slide the profile inwards in the direction of the arrow.

    • M8 × 20
  9. Prepare the components

    9. Prepare the components

    Make sure the assembly is as shown in the picture.

  10. Align the system

    10. Align the system

    Angle bolts are used to prevent the profile from sagging due to the heavy weight that can occur with long support arm profiles.

    • M8
    • M8 × 20
  11. Insert the gasket

    11. Insert the gasket

    Remove the yellow tape. Insert the cover seal with the adhesive surface to the black cover into its contour without folds.

  12. Fit the cover

    12. Fit the cover

    Place the cover on the module and tighten the screws.

    • M4 × 8
  13. Insert the gasket

    13. Insert the gasket

    Check whether the seal is seated well.

Select a step or use the arrows. On mobile, swipe left or right.