Skip to content

JOINT PARTS

Steel Wall Mounted Module - With Bellows

Request a quote
The cast steel wall module connects a support arm in the X-L system to a vertical mounting surface and forms the wall-side connection point of the assembly. It is intended for a horizontal support-arm connection. The joint technically permits a 90° pivot to the left and right. With the bellows fitted, a maximum pivot angle of 70° in each direction is recommended. The bellows enclose the moving joint area.
Weight
9500 g
Material
Cast steel
Colour
RAL 7035 (Bellow RAL 7016)
Package Dimensions
250 × 220 × 290 mm
HS Code
7606.99.90.19
Warranty
5 years

Technical data

Specifications for planning, selection and use at a glance.

Material & finish

Material Composition
Cast steel
Colour
RAL 7035 (Bellow RAL 7016)
RAL colours
RAL 7035 / RAL 7016

Application & function

Operating Weight
9500 g
Primary Use Case
Machine Building / Automation / HMI operator stations
Operating Temperature
–40°C to +70°C
Protection Rating
–IP65 (DIN EN 60529)
Rated Voltage
Mechanical (not subject to electrical certification)
Movement
Right 90° / Left 90°

Safety & compliance

Earthing
Yes, integrated solution
RoHS Compliance
RoHS EU Directive 2011/65/EU
REACH Compliance
REACH Regulation 1907/2006/EC
Certification
IEC 60529; (EG) No. 765/2008; (EU) 2023/956

Further information

Movement type
schwenkbar
Swivel angle right
90 deg
Swivel angle left
90 deg

Version & enquiry

Use the item number and version to prepare your enquiry.

  • SKU: X-L-WMF01

    Weight (g)
    9500

Product documents

Product files and documentation together in one place.

3 files

ZIP 1 file
PDF 2 files
  • X-L-WMF01-Produktunterlagen-DE.pdf

    2.3 MB

  • X-L-WMF01-Produktunterlagen-EN.pdf

    2.3 MB

Assembly instructions

About these instructions

Assembly sequence prepared from the exact XINDUX article data sheet. Tightening torques not specified in the source document are deliberately not added.

Preparation & tools

Supplied and installation parts

Supplied and installation parts

Required tools

  • Allen key suitable for the fasteners
  • Torque wrench for the final engineering check

Step 1 / 13 · Prepare the components

  1. Prepare the components

    1. Prepare the components

    The supporting axis of the module must be aligned vertically in accordance with the example assembly shown. Other mounting orientations are not permitted.

  2. Fasten the connection

    2. Fasten the connection

    Insert the angle bolts into their slots and tighten.

    • M8 × 20
  3. Insert the gasket

    3. Insert the gasket

    Insert the seal of the first connection with the adhesive surface to the component into the holder shown without folds.

  4. Connect the profile

    4. Connect the profile

    Insert the profile into the coupling as shown in the figure on the left.

    • M8 × 20
  5. Fasten the connection

    5. Fasten the connection

    Tighten the profile bolts.

    • M8 × 40
    • J8.4
    • M8
  6. Align the system

    6. Align the system

    Check the support arm profile with a spirit level. Only if there is visible deflection, loosen the four M8 × 40 profile bolts by 2-3 mm depending on the required correction angle, align the profile with the two M8 × 20 angle bolts and then tighten all profile bolts again.

    • M8 × 40
    • M8 × 20
  7. Fit the cover

    7. Fit the cover

    Install the bellows in the direction of the arrow as shown in the figure to cover the module.

  8. Fit the cover

    8. Fit the cover

    Insert the bellows coupling parts into the slots on the two ends of the bellows and tighten them well.

  9. Fit the cover

    9. Fit the cover

    Swivelling 90° to the left and right is technically possible. With bellows fitted, a maximum swivel angle of 70° in each direction is recommended.

    Check the bellows for a good fit.

  10. Insert the gasket

    10. Insert the gasket

    Insert the seal of the second connection with the adhesive surface to the component into the holder shown without folds.

  11. Fasten the connection

    11. Fasten the connection

    The M8 wall mounting screws are not included.

    The M8 wall mounting screws are not included.

    • M8
  12. Fit the cover

    12. Fit the cover

    Don't forget to install the module's plastic covers.

    Don't forget to install the module's plastic covers.

  13. Prepare the mounting holes

    13. Prepare the mounting holes

    Prepare four mounting holes Ø13 mm with a horizontal spacing of 130 mm and a vertical spacing of 110 mm according to the drawing. Allow for the central cable passage shown. The cable passage is not dimensioned in this drawing. All dimensions are given in millimetres.

Select a step or use the arrows. On mobile, swipe left or right.