Skip to content

PANEL COUPLING

Rotatable Panel Coupling

Request a quote
The rotary panel coupling connects a support arm in the X-L system to the operator enclosure. The rotary connection allows the connected panel to be aligned at the workstation while the support-arm attachment remains in place. Positioned directly at the transition to the enclosure, the coupling provides the articulated connection at this point. A clamping lever allows the rotational resistance of the connection to be adjusted.
Weight
1300 g
Material
Aluminum
Colour
RAL 7035
Package Dimensions
150 × 60 × 145 mm
HS Code
7606.99.90.19
Warranty
5 years

Technical data

Specifications for planning, selection and use at a glance.

Material & finish

Material Composition
Aluminum
Colour
RAL 7035
RAL colours
RAL 7035

Application & function

Operating Weight
1300 g
Primary Use Case
Machine Building / Automation / HMI operator stations
Operating Temperature
–40°C to +70°C
Protection Rating
–IP65 (DIN EN 60529)
Rated Voltage
Mechanical (not subject to electrical certification)
Movement
Rotatable 315°
Rotation angle
315 deg

Safety & compliance

Earthing
Yes, integrated solution
RoHS Compliance
RoHS EU Directive 2011/65/EU
REACH Compliance
REACH Regulation 1907/2006/EC
Certification
IEC 60529; (EG) No. 765/2008; (EU) 2023/956

Further information

Diameter
133 mm

Version & enquiry

Use the item number and version to prepare your enquiry.

  • SKU: X-L-PKD01

    Weight (g)
    1300

Product documents

Product files and documentation together in one place.

3 files

ZIP 1 file
PDF 2 files
  • X-L-PKD01-Produktunterlagen-DE.pdf

    2 MB

  • X-L-PKD01-Produktunterlagen-EN.pdf

    2 MB

Assembly instructions

About these instructions

Assembly sequence prepared from the exact XINDUX article data sheet. Tightening torques not specified in the source document are deliberately not added.

Preparation & tools

Supplied and installation parts

Supplied and installation parts

Required tools

  • Allen key suitable for the fasteners
  • Torque wrench for the final engineering check

Step 1 / 14 · Insert the gasket

  1. Insert the gasket

    1. Insert the gasket

    Remove the yellow tape. Insert the profile-side connection seal with the adhesive surface to the component into the seal holder shown without folds.

  2. Connect the profile

    2. Connect the profile

    Insert the profile into the coupling as shown in the figure on the left.

  3. Fasten the connection

    3. Fasten the connection

    Rotate the inner moving part to the first mounting position shown.

  4. Fasten the connection

    4. Fasten the connection

    Tighten the two M8 × 40 profile bolts of the first mounting position evenly.

    • M8 × 40
  5. Fasten the connection

    5. Fasten the connection

    Rotate the inner movable part to the second mounting position shown.

  6. Fasten the connection

    6. Fasten the connection

    Tighten the two M8 × 40 profile bolts of the second mounting position evenly.

    • M8 × 40
  7. Prepare the components

    7. Prepare the components

    Insert the plastic plugs into the slots.

  8. Set the rotation range

    8. Set the rotation range

    Install the M8 × 25 set screw.

    • M8 × 25
  9. Set the rotation range

    9. Set the rotation range

    Attention: You can limit the clockwise and counterclockwise rotation of the module with M8 × 25 screws.

    Attention: You can limit the clockwise and counterclockwise rotation of the module with M8 × 25 screws. There are 4 holes on the module. Optionally you can limit the rotation with 1 screw.

    • M8 × 25
  10. Insert the gasket

    10. Insert the gasket

    Remove the yellow tape. Insert the seal to the mounting surface with the adhesive surface to the component into the seal holder shown without folds.

  11. Align the system

    11. Align the system

    Insert the switching lever into the slot. The switching lever is used to adjust the torsional rigidity of the module.

    • M6 × 25
  12. Fasten the module to the panel

    12. Fasten the module to the panel

    The mounting screws are not included. Source conflict: the assembly instructions specify M8 × 30 for panel mounting; the interface drawing shows Ø7 mm holes and M6. Confirm the correct bolt and hole assignment with the manufacturer before installation.

    Attach the module to the panel with four M8 × 30 screws. The mounting screws are not included.

    • M8 × 30
  13. Fasten the module to the panel

    13. Fasten the module to the panel

    Check the module and panel connections for proper installation.

  14. Prepare the mounting holes

    14. Prepare the mounting holes

    If required, prepare the mounting holes according to the dimensioned drawing. All dimensions are given in millimetres.

Select a step or use the arrows. On mobile, swipe left or right.