Skip to content

JOINT PARTS

Rotatable Wall-Mounted Hinge Horizontal Outlet

Request a quote
The rotary wall joint attaches a support arm in the X-L system to the side of a wall or machine structure. Its horizontal profile outlet directs the arm away from the mounting surface. The rotary connection allows the connected arm to pivot in the horizontal plane. The joint forms the articulated wall-side connection point through which the operator enclosure can be positioned at the workstation.
Weight
6500 g
Material
Aluminum
Colour
RAL 7035 (Cover RAL 7016)
Package Dimensions
390 × 200 × 210 mm
HS Code
7606.99.90.19
Warranty
5 years

Technical data

Specifications for planning, selection and use at a glance.

Material & finish

Material Composition
Aluminum
Colour
RAL 7035 (Cover RAL 7016)
RAL colours
RAL 7035 / RAL 7016

Application & function

Operating Weight
6500 g
Primary Use Case
Machine Building / Automation / HMI operator stations
Operating Temperature
–40°C to +70°C
Protection Rating
–IP65 (DIN EN 60529)
Rated Voltage
Mechanical (not subject to electrical certification)
Movement
Rotatable 315°
Rotation angle
315 deg

Safety & compliance

Earthing
Yes, integrated solution
RoHS Compliance
RoHS EU Directive 2011/65/EU
REACH Compliance
REACH Regulation 1907/2006/EC
Certification
IEC 60529; (EG) No. 765/2008; (EU) 2023/956

Version & enquiry

Use the item number and version to prepare your enquiry.

  • SKU: X-L-WGH01

    Weight (g)
    6500

Product documents

Product files and documentation together in one place.

3 files

ZIP 1 file
PDF 2 files
  • X-L-WGH01-Produktunterlagen-DE.pdf

    2 MB

  • X-L-WGH01-Produktunterlagen-EN.pdf

    2 MB

Assembly instructions

About these instructions

Assembly sequence prepared from the exact XINDUX article data sheet. Tightening torques not specified in the source document are deliberately not added.

Preparation & tools

Supplied and installation parts

Supplied and installation parts

Required tools

  • Allen key suitable for the fasteners
  • Torque wrench for the final engineering check

Step 1 / 12 · Fasten the connection

  1. Fasten the connection

    1. Fasten the connection

    Insert the angle bolts into their slots and tighten.

    • M8 × 20
  2. Insert the gasket

    2. Insert the gasket

    Remove the yellow tape. Insert the profile-side connection seal with the adhesive surface to the component into the seal holder shown without folds.

  3. Align the system

    3. Align the system

    Angle bolts are used to prevent the profile from sagging due to the heavy weight that can occur with long support arm profiles. M8 × 20 angle bolts prevent weight-related sagging in long support arm profiles. If no sagging occurs, the angle bolts remain in the tightened position. If there is deflection, loosen the M8 × 40 profile bolts by 2-3 mm depending on the required angle, align the profile and then tighten it again. Check the inclination with a spirit level.

    • M8 × 40
    • J8.4
    • M8
    • M8 × 20
  4. Set the rotation range

    4. Set the rotation range

    Attention: You can limit the clockwise and counterclockwise rotation of the module with M8 × 10 screws.

    Attention: You can limit the clockwise and counterclockwise rotation of the module with M8 × 10 screws. There are eight equally spaced holes on the module. Optionally you can set the rotation limits with two screws.

    • M8 × 10
  5. Install the cable guide

    5. Install the cable guide

    Place the plastic cable protector as shown in the illustration on the left.

  6. Insert the gasket

    6. Insert the gasket

    Remove the yellow tape. Insert the cover seal with the adhesive surface to the black cover into its contour without folds.

  7. Fit the cover

    7. Fit the cover

    Position the top case cover and secure with the screws shown.

  8. Connect the grounding

    8. Connect the grounding

    Caution: Make the ground connection and check that it is secure.

    Caution: Make the ground connection and check that it is secure.

    • M6 × 10
  9. Fit the cover

    9. Fit the cover

    Position the side case cover and secure with the screws shown.

  10. Insert the gasket

    10. Insert the gasket

    Remove the yellow tape. Insert the seal to the mounting surface with the adhesive surface to the component into the seal holder shown without folds.

  11. Fit the cover

    11. Fit the cover

    The M8 mounting screws are not included.

    Place the black screw caps on the heads of the M8 screws. The M8 mounting screws are not included.

    • M8
  12. Prepare the mounting holes

    12. Prepare the mounting holes

    If required, prepare the mounting holes according to the dimensioned drawing. All dimensions are given in millimetres.

Select a step or use the arrows. On mobile, swipe left or right.