
PANEL COUPLING
Rotatable Panel 90° Angle Coupling
- Weight
- 2400 g
- Material
- Aluminum
- Colour
- RAL 7035 (Cover RAL 7016)
- Package Dimensions
- 220 × 150 × 170 mm
- HS Code
- 7606.99.90.19
- Warranty
- 5 years
Technical data
Specifications for planning, selection and use at a glance.
Material & finish
- Material Composition
- Aluminum
- Colour
- RAL 7035 (Cover RAL 7016)
- RAL colours
- RAL 7035 / RAL 7016
Application & function
- Operating Weight
- 2400 g
- Primary Use Case
- Machine Building / Automation / HMI operator stations
- Operating Temperature
- –40°C to +70°C
- Protection Rating
- –IP65 (DIN EN 60529)
- Rated Voltage
- Mechanical (not subject to electrical certification)
- Movement
- Rotatable 315°
- Rotation angle
- 315 deg
Safety & compliance
- Earthing
- Yes, integrated solution
- RoHS Compliance
- RoHS EU Directive 2011/65/EU
- REACH Compliance
- REACH Regulation 1907/2006/EC
- Certification
- IEC 60529; (EG) No. 765/2008; (EU) 2023/956
Further information
- Diameter
- 133.5 mm
Version & enquiry
Use the item number and version to prepare your enquiry.
| Choose a version | ||
|---|---|---|
| SKU: X-L-PWK01 | 2400 |
SKU: X-L-PWK01
- Weight (g)
- 2400
Assembly instructions
About these instructions
Assembly sequence prepared from the exact XINDUX article data sheet. Tightening torques not specified in the source document are deliberately not added.
Preparation & tools
Supplied and installation parts

Required tools
- Allen key suitable for the fasteners
- Torque wrench for the final engineering check

1. Fasten the connection
Insert the angle bolts into their slots and tighten.
- M8 × 20

2. Insert the gasket
Remove the yellow tape. Insert the profile-side connection seal with the adhesive surface to the component into the seal holder shown without folds.

3. Connect the profile
Insert the profile into the coupling as shown in the figure on the left.
- M8 × 20

4. Fasten the connection
Tighten the profile bolts.
- M8 × 30
- J8.4

5. Align the system
Check the support arm profile with a spirit level. Only if there is visible deflection, loosen the M8 × 40 profile bolts by 2-3 mm depending on the required correction angle, align the profile with the M8 × 20 angle bolts and then tighten all profile bolts again.
- M8 × 40
- M8 × 20

6. Insert the gasket
Remove the yellow tape. Insert the cover seal with the adhesive surface to the black cover into its contour without folds.

7. Align the system
The switching lever is used to adjust the torsional rigidity of the module.
- M4 × 8

8. Prepare the components
Insert the plastic plugs into the slots provided.

9. Set the rotation range
Install the M8 × 25 set screw.
- M8 × 25

10. Set the rotation range
Attention: The angle limiting screw (M8 × 25) can be used when the module rotation angle is to be reduced.
Attention: The angle limiting screw (M8 × 25) can be used when the module rotation angle is to be reduced. There are four holes on the module.
- M8 × 25

11. Insert the gasket
Remove the yellow tape. Insert the seal to the mounting surface with the adhesive surface to the component into the seal holder shown without folds.

12. Fasten the module to the panel
Bolts and washers are not included.
Place the module on the panel. Bolts and washers are not included.
- M8 × 30
- J8.4

13. Prepare the mounting holes
If required, prepare the mounting holes according to the dimensioned drawing. All dimensions are given in millimetres.
Select a step or use the arrows. On mobile, swipe left or right.
Products in this series
Warning Lamp Cover (M22)
Rotatable Panel Coupling
Panel Coupling
Warning Lamp Cover (M18)
130/080 Support Arm Adaptor
Wall-Socket Mounting Bracket
Height Adjustable Support Arm
Steel Wall Mounted Module - With Bellows
Rotatable Intermediate Hinge
Rotatable Wall-Mounted Hinge Horizontal Outlet
Rotatable Top Mounted Vertical Outlet
90° Angle Piece
Rotatable Top Mounted 90° Angle Joint
Rotatable profile joint
Steel Interconnection Module - With Bellows
Rotatable Wall-Mounted Hinge Vertical Outlet
kiosk base with levelling feet
kiosk base with flange
mobile kiosk base with castors
130 Support Profile - 1000mm · X-L
