Skip to content

JOINT PARTS

Wall-Socket Mounting Bracket

Request a quote
The fixed wall mounting connects a support-arm profile in the X-L system to a vertical or horizontal mounting surface. It forms a rigid attachment point and has no rotary function. The component sits between the mounting structure and profile. It is suited to assemblies where this connection is to remain fixed and the operator enclosure is positioned using other joints in the support arm.
Weight
1000 g
Material
Aluminum
Colour
RAL 7035 (Cover RAL 7016)
Package Dimensions
220 × 50 × 110 mm
HS Code
7606.99.90.19
Warranty
5 years

Technical data

Specifications for planning, selection and use at a glance.

Material & finish

Material Composition
Aluminum
Colour
RAL 7035 (Cover RAL 7016)
RAL colours
RAL 7035 / RAL 7016

Application & function

Operating Weight
1000 g
Primary Use Case
Machine Building / Automation / HMI operator stations
Operating Temperature
–40°C to +70°C
Protection Rating
–IP65 (DIN EN 60529)
Rated Voltage
Mechanical (not subject to electrical certification)
Movement
Fixed

Safety & compliance

Earthing
Yes, integrated solution
RoHS Compliance
RoHS EU Directive 2011/65/EU
REACH Compliance
REACH Regulation 1907/2006/EC
Certification
IEC 60529; (EG) No. 765/2008; (EU) 2023/956

Further information

Movement type
fest

Version & enquiry

Use the item number and version to prepare your enquiry.

  • SKU: X-L-WBF01

    Weight (g)
    1000

Product documents

Product files and documentation together in one place.

3 files

ZIP 1 file
PDF 2 files
  • X-L-WBF01-Produktunterlagen-DE.pdf

    1.5 MB

  • X-L-WBF01-Produktunterlagen-EN.pdf

    1.5 MB

Assembly instructions

About these instructions

Assembly sequence prepared from the exact XINDUX article data sheet. Tightening torques not specified in the source document are deliberately not added.

Preparation & tools

Supplied and installation parts

Supplied and installation parts

Required tools

  • Allen key suitable for the fasteners
  • Torque wrench for the final engineering check

Step 1 / 11 · Fasten the connection

  1. Fasten the connection

    1. Fasten the connection

    Insert the angle bolts into their slots and tighten.

    • M8 × 20
  2. Insert the gasket

    2. Insert the gasket

    Remove the yellow tape. Insert the profile-side connection seal with the adhesive surface to the component into the seal holder shown without folds.

  3. Connect the profile

    3. Connect the profile

    Insert the profile into the coupling as shown in the figure on the left.

    • M8 × 20
  4. Fasten the connection

    4. Fasten the connection

    Tighten the profile bolts.

    • J8.4
    • M8 × 40
  5. Align the system

    5. Align the system

    Source conflict: the assembly source first identifies M8 × 20 as angle bolts, but refers to M8 × 40 when retightening them. Confirm the bolt assignment and adjustment procedure with the manufacturer before proceeding.

    Angle bolts are used to prevent the profile from sagging due to the heavy weight that can occur with long support arm profiles. Use M8×20 screws for angle correction. If sagging does not occur in your application, leave the angle bolts in the tightened position. If there is deflection in your application, loosen the M8 × 40 profile bolts by 2-3mm depending on the desired angle. Once the profile is adjusted to the desired position, retighten the M8 × 40 angle screws. Then check the inclination with a spirit level.

    • M8
    • M8 × 20
    • M8 × 40
  6. Connect the grounding

    6. Connect the grounding

    Caution: Make the ground connection and check that it is secure.

    Caution: Make the ground connection and check that it is secure.

    • M6 × 10
  7. Insert the gasket

    7. Insert the gasket

    Remove the yellow tape. Insert the seal to the mounting surface with the adhesive surface to the component into the seal holder shown without folds.

  8. Insert the gasket

    8. Insert the gasket

    Check whether the seal is seated well.

  9. Fasten the connection

    9. Fasten the connection

    The M8 mounting screws are not included. Source conflict: the assembly source specifies M8 mounting bolts; the catalogue connection drawing specifies Ø13 / M12. Confirm the applicable interface and mounting fasteners with the manufacturer before assembly.

    The M8 mounting screws are not included.

    • M8
  10. Fit the cover

    10. Fit the cover

    Don't forget to install the module's plastic covers.

    Don't forget to install the module's plastic covers.

  11. Prepare the mounting holes

    11. Prepare the mounting holes

    If required, prepare the mounting holes according to the dimensioned drawing. All dimensions are given in millimetres.

Select a step or use the arrows. On mobile, swipe left or right.