
JOINT PARTS
Rotatable Top Mounted Vertical Outlet
- Weight
- 4800 g
- Material
- Aluminum
- Colour
- RAL 7035 (Cover RAL 7016)
- Package Dimensions
- 220 × 125 × 205 mm
- HS Code
- 7606.99.90.19
- Warranty
- 5 years
Technical data
Specifications for planning, selection and use at a glance.
Material & finish
- Material Composition
- Aluminum
- Colour
- RAL 7035 (Cover RAL 7016)
- RAL colours
- RAL 7035 / RAL 7016
Application & function
- Operating Weight
- 4800 g
- Primary Use Case
- Machine Building / Automation / HMI operator stations
- Operating Temperature
- –40°C to +70°C
- Protection Rating
- –IP65 (DIN EN 60529)
- Rated Voltage
- Mechanical (not subject to electrical certification)
- Movement
- Rotatable 315°
- Rotation angle
- 315 deg
Safety & compliance
- Earthing
- Yes, integrated solution
- RoHS Compliance
- RoHS EU Directive 2011/65/EU
- REACH Compliance
- REACH Regulation 1907/2006/EC
- Certification
- IEC 60529; (EG) No. 765/2008; (EU) 2023/956
Version & enquiry
Use the item number and version to prepare your enquiry.
| Choose a version | ||
|---|---|---|
| SKU: X-L-AGV01 | 4800 |
SKU: X-L-AGV01
- Weight (g)
- 4800
Assembly instructions
About these instructions
Assembly sequence prepared from the exact XINDUX article data sheet. Tightening torques not specified in the source document are deliberately not added.
Preparation & tools
Supplied and installation parts

Required tools
- Allen key suitable for the fasteners
- Torque wrench for the final engineering check

1. Insert the gasket
Remove the yellow tape. Insert the profile-side connection seal with the adhesive surface to the component into the seal holder shown without folds.

2. Connect the profile
Insert the support arm profile into the profile-side connection of the rotatable top mounting module until it rests.

3. Fasten the connection
Fasten the support arm profile evenly with four M8 × 40 profile bolts and four J8.4 lock washers.
- M8 × 40
- J8.4

4. Connect the grounding
Insert a Ø5 mm grounding ball, a Ø5 × 13 mm compression spring and a Ø8 × 5 mm plastic plug into the profile connection receptacles shown.

5. Fasten the connection
Connect the profile coupling housing to the pivot bearing unit and fasten the connection evenly with eight M8 × 16 screws with thread lock.
- M8 × 16

6. Set the rotation range
Set the desired rotation range using the eight evenly spaced stop holes. Use one M8 × 10 rotation limit screw for each desired stop. A screw is included in the scope of delivery shown; a second one is required for two stops.
- M8 × 10

7. Set the rotation range
Screw an M8 × 25 set screw into the radial threaded hole shown on the support arm profile. Align the set screw with the previously inserted plastic plug.
- M8 × 25

8. Inspect the assembly
Check whether the profile coupling housing and pivot bearing unit are assembled flush and all eight connecting screws are fully seated.

9. Prepare the components
Insert the pre-assembled profile coupling and pivot bearing unit completely into the top assembly base body.

10. Fasten the connection
Attach the pivot bearing assembly evenly to the top mount base body with eight M8 × 25 screws.
- M8 × 25

11. Connect the grounding
Attach the protective conductor to the marked ground connection on the bottom with an M6 × 10 screw and check that it is secure.
- M6 × 10

12. Insert the gasket
Remove the yellow tape. Insert the seal to the mounting surface with the adhesive surface to the component into the seal holder shown without folds.

13. Fit the cover
The mounting screws are not included.
Place four black caps on the heads of the four M12 mounting screws. The mounting screws are not included.
- M12

14. Prepare the mounting holes
If required, prepare the mounting holes according to the dimensioned drawing. All dimensions are given in millimetres.
Select a step or use the arrows. On mobile, swipe left or right.
Products in this series
Warning Lamp Cover (M22)
Rotatable Panel Coupling
Panel Coupling
Warning Lamp Cover (M18)
130/080 Support Arm Adaptor
Wall-Socket Mounting Bracket
Height Adjustable Support Arm
Steel Wall Mounted Module - With Bellows
Rotatable Intermediate Hinge
Rotatable Wall-Mounted Hinge Horizontal Outlet
90° Angle Piece
Rotatable Panel 90° Angle Coupling
Rotatable Top Mounted 90° Angle Joint
Rotatable profile joint
Steel Interconnection Module - With Bellows
Rotatable Wall-Mounted Hinge Vertical Outlet
kiosk base with levelling feet
kiosk base with flange
mobile kiosk base with castors
130 Support Profile - 1000mm · X-L
